Sophos-branded physical appliance web console
The web console lets you view appliance status, configure basic settings, and troubleshoot a Sophos-branded physical appliance from a browser. It includes information and features that are also available from the LCD panel and serial console.
See Sophos-branded physical appliance LCD panel and Sophos-branded physical appliance serial console.
The web console uses HTTPS on port 4444. It includes tabs to access different features and information. The available tabs depend on whether the appliance has been activated and set up, as follows:
- Before activation, the web console shows the Activation, Maintenance, and Download Logs tabs.
- After activation and setup, it shows the Dashboard, System Info, Network, Maintenance, Download Logs, and Actions tabs.
Access the web console
You must connect your computer directly to the management port. The management port uses the IP address 10.0.1.1 with a /24 subnet. To access the web console, go to https://10.0.1.1:4444 in your browser.
Note
The web console is only available through the dedicated management port. You can't access it through the EXTP port.
Your browser shows a certificate warning when you first open the web console. This is expected because the appliance generates the certificate used by the web console. You can continue to the web console after acknowledging the warning in your browser.
The management port IP address can't be changed. If your network already uses the 10.0.1.0/24 network, connect your computer directly to the management port instead of connecting the management port to your network.
Sign in
Sign in to the web console with these default credentials:
- Username:
admin - Password:
admin
The web console password is separate from the appliance command-line interface (CLI) password. Changing the web console password doesn't change the CLI password.
You must change the default web console password before you connect the appliance to your network.
To change the password, do as follows:
- Go to the Actions tab.
-
Click Change Password and enter a new password.
The password must be between 8 and 128 characters.
Changing the password signs out any other web console sessions using the same account.
Your web console session ends in the following situations:
- You click Log Off on the Actions tab.
- The session is inactive for five minutes.
- The web console restarts.
Web console tabs
The System Info, Network, and Maintenance tabs show live appliance information. Refresh the page to see the latest information.
Activation
The Activation tab is available before appliance activation is complete. It shows the same activation information as the LCD panel, including recent activation events and the progress of the system image download and installation. See Troubleshooting activation.
If DHCP fails, Static IP Setup lets you configure the network settings manually. Enter the IP address, subnet mask, and gateway, then click Apply Static IP. You can enter the subnet mask in dotted-decimal or CIDR notation. Click Cancel to return to DHCP.
If the page shows "We are upgrading. Please wait", the installer is updating. Wait for the update to finish, then click OK to reload the page.
Dashboard
The Dashboard tab shows the following information:
- Appliance details, including hostname, Unique Identification Number (UIN), Internal Device Name (IDN), date and time, serial number, MAC address, and firmware version.
- Resource usage, including CPU, memory, load, and disk usage.
The firmware version identifies the appliance firmware. NDR software updates don't change it, so it might not match the NDR version shown in Sophos Fusion.
The date and time come from the appliance, not from your browser.
If the hostname shows "PROVISIONING", the appliance hasn't finished registering yet.
System Info
The System Info tab shows detailed hardware and firmware information about the appliance.
Network
The Network tab shows the EXTP network settings, including the IP address, gateway, and DHCP status. It also shows information about the dedicated management port.
The tab also shows the following appliance traffic mode and capture interface information:
- For inline traffic, it shows throughput, packets per second, latency, and link status for each bridge.
- For sniffer traffic, it shows throughput, packets per second, and link status for each capture port.
You can change the EXTP network settings by using DHCP or specifying a static IP address.
Maintenance
Under the Maintenance tab, you can see the following sub-tabs:
- Network Info: Shows ARP information, routes, and network interface status.
- Diagnostics: Runs connectivity checks for the appliance. See Network diagnostics.
- Tools: Lets you run ping, TCP connection, OpenSSL, and traceroute tests. The tests use the EXTP interface to check connectivity from the appliance to the target.
- Packet Capture: Captures network traffic for 30 seconds. You can filter the capture by IP address and port and download the results when the capture finishes.
- Logs: Lets you view appliance logs and copy log information when you need it for troubleshooting.
Network diagnostics
The Diagnostics sub-tab runs connectivity checks in order. If a check fails, any checks that depend on it are skipped.
Fix the first failure, then run the diagnostics again.
| Check | What to do if it fails |
|---|---|
| EXTP interface | Check that the EXTP cable is connected and the port has a network link. |
| IP assignment | Make sure the EXTP interface has an IPv4 address. On the Network tab, use DHCP or configure a static IP address. |
| Default route | Make sure a default gateway is configured on the Network tab. |
| Gateway reachability | Check the EXTP connection and gateway address. Also check whether the gateway allows ICMP traffic from the appliance. |
| Sophos connectivity | Check that your firewall allows the required outbound connections from the appliance. See Connectivity requirements. |
Download Logs
The Download Logs tab creates a ZIP file containing appliance logs. Download the file if Sophos Support asks you to provide logs for troubleshooting.
The downloaded file is named ndr-<idn>.zip, where <idn> is the appliance's Internal Device Name.
Actions
The Actions tab lets you take the following actions:
- Restart the appliance.
- Shut down the appliance.
- Change the web console password.
- Sign out of the web console.
Troubleshooting
Can't reach the web console
Issue
You can't reach the web console.
What to do
- Check that your computer is connected to the appliance's dedicated management port.
- Check that your computer has an IP address that can communicate with
10.0.1.1/24. - Go to
https://10.0.1.1:4444in your browser. - If the appliance has just started, wait several minutes and try again.
If you still can't reach the web console, contact Sophos Support.
Certificate error after an IP address change
Issue
Your browser reports that the web console certificate doesn't match the appliance IP address after the address changes.
What to do
Contact Sophos Support.
Can't sign in to the web console
Issue
You can't sign in to the web console.
Possible causes are as follows:
- You're using the appliance CLI password instead of the web console password.
- You've forgotten the web console password.
What to do
Make sure you're using the web console password.
If you've forgotten it, contact Sophos Support.
Contact Sophos Support
If you contact Sophos Support about a web console issue, have the following information available:
- Appliance model and serial number
- Exact error message or a screenshot showing the issue
- Results from Maintenance > Diagnostics
- Log file downloaded from the Download Logs tab
- Network settings shown on the Network tab, if the issue is related to connectivity
Don't include your web console password.